UV-2C-T COMPORT MICRO PROCESSOR INTEGRATOR SD

The UV-2C-T COMPORT MICRO PROCESSOR INTEGRATOR SD is an economical, self-contained, high quality UV measuring instrument.

+ Choice of a combination of two different spectral ranges:
+ UV-A intensity mW/cm2 + UV-V dose mJ/cm2
+ UV-B intensity mW/cm2 + UV-V dose mJ/cm2
+ UV-C intensity mW/cm2 + UV-A dose mJ/cm2
+ UV-V intensity mW/cm2 + UV-V dose mJ/cm2
+ Temperature C/F
+ Permanent or triggered measuring mode*
+ SD Memory Card
+ Graphic chart on computer
+ Re-chargeable accu cells with charger

It is designed to measure, record and display peak UV intensity, UV dosage and temperature in the UV curing process.It is equipped with two different UV sensors and one temperature sensor for the individual measuring of a combination of either:

UV-C 230 280 nm
UV-B 280 315 nm
UV-A 315 400 nm
UV-V 395 445 nm
UV 250 410 nm

With two different UV-bands, many of the measuring requirements of UV curing applications can be covered. Due to its two different UV sensors and the integrated microprocessor the UV-2C Microprocessor Integrator can measure, record and display the peak of the UV-intensity (mW/cm2) for each UV-band individually. Additionally, this UV-Integrator is calculating the UV-dosage (mJ/cm2) of the UV energy supplied during the time of exposure of one measuring cycle. The UV-dosage is calculated for each UV-band (UV-A and UV-V) individually. This allows to determine not only the UV-energy, but also how that energy is delivered, i.e., what intensity and dose at what UV-band. An extra sensor measures temperatures from 32 to 230 F / 0 to 110 Celsius.

*This Microprocessor Integrator features a selectable triggered mode, i.e. the 30 sec recording cycle starts within a 120 second readiness phase not before the incident UV-intensity exceeds 2 mW/cm.

The three sensors are on the back of the unit which also serves as a heat shield. After completion of the measuring cycle all measuring results can be scrolled through on the built in 2 x 16 digit LCD display. A special AUTO-OFF feature that turns off the unit automatically after one minute serves as energy saving and extension of the battery service life. This microprocessor integrator is additionally equipped with an SD Memory Card. All measuring data are stored and can be downloaded to a computer. The special evaluation software allows to show, edit and store a history of the measuring results of the entire measuring cycle as graphic and numeric charts (mW/cm2) and (mJ cm2) and (C/F)and (F option -)

UV-2C-T SD Microprocessor Integrator UV-A + UV-V + Temp
UV-2C-T SD Microprocessor Integrator UV-A + UV-B + Temp
UV-2C-T SD Microprocessor Integrator UV + UV-A + Temp
UV-2C-T SD Microprocessor Integrator UV + UV-B + Temp
UV-2C-T SD Microprocessor Integrator UV + UV-V + Temp
UV-2C-T SD Microprocessor Integrator UV-B + UV-V + Temp
UV-2C-T SD Microprocessor Integrator UV-C + UV-V + Temp

TECHNICAL DATA
Spectral ranges: UV-A 315 410 nm, UV-B 280 315 nm, UV-C 230 280 nm, (UV-V 395 445 nm), UV 230 410 nm
Temperature range: 32 to 230 F / 0 to 110 C
Max. Power Input 0 to 5,000 mW/cm2
Measuring range: 0 to 2,000 mW/cm2
Sampling rate: 0.005 sec (200/sec)
Recording cycle: 30 sec.
Readiness phase: 120 sec.
Display range: 0 to 36,000 mJ/cm2
Display: LCD, 2 x 16 digits
Power source: 2 x 3.7 V LiPO Accu
Power consumption: 20 A
Accu service life: 1,000 re-charging cycles
Dimensions: 5.5 (140 mm), height (13 mm)
Weight: approx. 17.5 ounce (500 g)
Operating temperature: 32 to 113 F / 0 to 45 C
Heat protection: Heat shield on back plate
Base Accuracy: 5 %

While on the conveyer belt, the UV-2C-T SD Microprocessor Integrator can withstand max. 230 F / 110 C for up to 10 seconds. The temperature of the housing should not exceed 113 F / 45 C. Because of uneven radiation distribution of the UV light source and different type of construction of the measuring devices by different manufacturers, different readings may appear under the same measurement conditions.

CALIBRATION
In order to keep its full function and precision it is recommended to have re-calibration done once per year. Re-calibration will also be necessary after change of battery. PTB traceable calibration acc. to DIN EN ISO / IEC 17025 with certificate.

Download Datasheet:
UV-2C-T Comport Micro Processor Integrator.pdf